Single hung
Double hung
Horizontal roller
Casement
Bay & bow
Sliding glass doors
Entry doors
Impact garage doors
PGT
CGIFree in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Get your free estimateCGI Door Installation in Whitney: What to Know First
CGI door installation in Whitney runs $1,850 to $4,200 for a standard entry door (unit plus install), and $2,600 to $6,800 for hurricane-rated French or double doors, depending on the series, sizing and jamb condition. We’re an independent installer working with CGI products, and most straightforward Whitney replacements get measured, ordered and installed inside three to five weeks once the unit arrives. If you’ve gotten a quote from a national chain with a ticket number and a callback window, we do this differently: you’ll talk to a real person, get a written line-item estimate, and know exactly who’s pulling into your driveway.
This page is for Whitney homeowners whose CGI doors need replacing, upgrading or resizing after a failed install or a storm event. Call (844) 797-3297 for a free estimate.
How CGI Products Fail – and How We Fix Them
CGI makes solid door systems, but every product has weak points, and the Whitney climate exposes them. Here’s what we actually see on CGI jobs across the valley:
- Water intrusion at the sill on CGI entry doors. Whitney’s monsoon season pushes wind-driven rain sideways, and a sill pan that wasn’t sloped or sealed correctly lets water pool under the door. We see rotting subfloor and swollen thresholds on units that were installed fast. We reset the sill with a proper pan, slope and backer rod, then verify with a hose test.
- Jamb racking on CGI French and double doors. CGI’s multi-panel French doors need a plumb, square opening; when the rough-in is off even a quarter inch, the active panel drags and the astragal seal fails. We check the opening with a laser and shim the frame true before the door ever goes in.
- Hardware drift on older CGI sliding entry lines. Rollers flatten and the track collects desert grit, so the door jumps or binds. We replace the roller assemblies with a quality aftermarket set sized to the original track profile, and we ream and clean the track rather than replace it when it’s still true.
- Glazing seal failure from heat cycling. Whitney hits 110°F in summer and drops into the 40s in winter, and that swing stresses the perimeter seals on insulated glass. Fogging between panes is the tell. On CGI units still under the manufacturer’s glass warranty, we document and route the claim; on out-of-warranty units we set a new glazed panel.
- Strike plate misalignment after a wall shift. Stucco movement and slab settling move the strike just enough that the deadbolt won’t seat. We re-mortise and re-set the strike with a longer screw into framing rather than shimming the plate, which is the lazy fix that comes loose in a year.
One thing that surprises owners: CGI’s OEM replacement hardware often costs more than a comparable quality aftermarket part, and the warranty terms differ. We’ll tell you which path keeps your coverage intact and which doesn’t – because on some CGI series, non-OEM hardware voids the finish warranty even when the part is better.
Styles & brands we work with
- Single hung
- Double hung
- Horizontal roller
- Casement
- Bay & bow
- Sliding glass doors
- Entry doors
- Impact garage doors
- PGT
- CGI
Our CGI Door Installation Process
Here’s exactly how a CGI door job runs from your first call to the final walkthrough.
- 1
Call and measure. A live person answers any hour. We schedule a measurement visit, confirm the CGI series and model on your existing unit, and check the rough opening, sill and jamb condition.
- 2
Written, line-item estimate. You get the unit cost, labor, permit fees if any, and disposal in writing. No change orders unless you change the scope.
- 3
Parts decision. We walk you through OEM vs quality aftermarket on hinges, locks, rollers and sills, and flag which choice affects warranty coverage on your specific CGI model.
- 4
Install day. Our technicians are background-checked and arrive in uniform. We protect the floor, pull and reset the frame plumb and square, set the sill pan, seal the perimeter per Florida product approval where required, and hang the door true.
- 5
Test and adjust. We cycle the door, check the lock and deadbolt engagement, run a hose test on the sill and perimeter, and adjust strike and weatherstrip until it closes clean with one hand.
- 6
Cleanup and guarantee. We haul away the old unit and packaging, walk you through the finished job, and stand behind it under the 36500-Day Done Right Promise – if something isn’t right, we come back and make it right.
See the difference
Before
After
Before
After
Before
AfterWhat CGI Door Installation Costs in Whitney
Pricing depends on the CGI series, door size and whether we’re resetting the frame or replacing just the slab. Here are the ranges we see most often in Whitney:
| Scenario | Typical Range |
|---|---|
| Single entry door, standard CGI series, full unit | $1,850 – $3,200 |
| Hurricane-rated entry door, impact glazing | $2,400 – $4,200 |
| French or double door, CGI impact-rated | $2,600 – $6,800 |
| Slab replacement only (frame stays) | $950 – $1,800 |
| Hardware, sill and weatherstrip rework | $180 – $650 |
What moves the price: door size, impact glass vs standard, whether the rough opening needs correction, and any permit or Florida product approval requirements. We pull and pass every permit the job needs. Call (844) 797-3297 for a free, no-trip-charge estimate inside the county.
Why Whitney Homeowners Call Winslow Windows & Doors Whitney for CGI Work
Ed Winslow’s name is on every job, and that matters when you’re spending thousands on a door that has to hold up to Whitney’s heat, wind and monsoon rain. Our technicians have up to 15 years of experience on impact-rated products, and they know CGI doors specifically – the sill details, the hardware trade-offs, the warranty-safe ways to make a repair last. As an independent CGI installer, we work with the brand but aren’t authorized by the manufacturer, which means we can recommend the right fix instead of the manufacturer-mandated one. We also handle PGT, CWS, ES Windows and ECO Window Systems doors, so if a brand comparison makes sense, we can walk you through it honestly. Upfront pricing, a live person on the line 24/7, and a real neighbor you can call at 2 a.m. – that’s the difference.
FAQs
Not if it’s installed to CGI’s published installation specs and Florida product approval. We follow those specs and document the install, so your glass and finish warranty stay in force. Call (844) 797-3297 if you’re unsure whether a prior install was done correctly.
In most cases, yes. Common CGI series are available through authorized channels, and for hardware we can usually source a quality aftermarket equivalent that fits your existing track and hinge prep. Lead time typically runs two to four weeks for the door unit. Call for a current availability check.
Replace if the frame is out of square, the glass is fogged or the subfloor shows water damage; repair if the issue is limited to hardware, weatherstrip or a misaligned strike. We’ll give you a written line-item estimate on both so you can compare. Estimates are free.
Most Whitney installations happen three to five weeks after the order is placed, once the unit arrives. Simple slab or hardware jobs can often be scheduled sooner. Call (844) 797-3297 to get on the schedule.
Yes. We install hurricane-rated CGI entry and French doors with impact glazing, installed to Florida product approval. We pull the permits and pass the inspections. Call for an exact quote on your opening.
Written by the team at Winslow Windows & Doors Whitney, serving Whitney and nearby areas.